Exactly How to Replace a Tub Yourself: Removing and Replacing.
Exactly How to Replace a Tub Yourself: Removing and Replacing.
Blog Article
We have found this article involving How to Install a Bathtub directly below on the web and reckoned it made sense to talk about it with you in this article.
Installing a bath tub isn't specifically rocket science, yet it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is additionally a moderately difficult task. If the old bathtub is easily available, the project can relocate easily; if you need to open a wall to get rid of the old bathtub and place the new bath tub, the task is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly require a helper to leave the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the task and fit attempting it. Instead of working with a specialist to take control of a halfway-completed job, it is far better to think about using one before you start. Chances are you might need an expert plumber to make tube connections.
This post will certainly assist you mount a new bath tub in your bathroom if you have currently purchased a brand-new tub as well as do not need to transform the arrangement of your previous water pipes.
Your devices as well as product checklist need to make up the following:
Planning for the Setup
To start with, the supporting structure supplied with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid pressure on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you use all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water. After doing so, activate the taps to drain any type of water staying in the system. The process of eliminating the existing taps can be quite troublesome because of the restricted gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipes have been gotten rid of, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Before going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Setting up the Bathtub
Using both wood boards under its feet, put the tub in the required position. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to ensure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the tub until the level reviews level.
To install faucets, fit the bottom of the furthest adaptable faucet connector to the appropriate supply pipeline by making a compression join; then do the very same for the other tap.
Activate the supply of water and examine all joints as well as new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the producer's user's manual. Tiling as well as sealing around the tub ought to wait till the tub has actually been utilized at least when as this will resolve it into its last position.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin guaranteeing that the washing machines are in area between the tap and also the sink. Secure the faucet in position with the producer given backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous kind needs to be connected to the tap ends first, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, causing the water to permeate the wall surface in between the bathroom and the tiling, resulting in issues with wetness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealant can break relatively early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the marketplace. It is recommended to fit the tiles using waterproof or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very focused on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you appreciated the blog posting. Enjoyed reading our piece of writing? Please share it. Let others find it. Thank you for your time. Don't forget to check up our website back soon.
Source Report this page